To safely clean and maintain your Combisteel 7450.0563 refrigerator, always isolate the power supply before washing, clean the interior and shelves regularly without abrasive agents, wipe door seals using water only, prevent cleaning wash from entering the internal drain hole, and periodically clean the condenser.
Applies to
This care guide applies strictly to the Combisteel 7450.0563 two-door commercial refrigerator.
Before you start
- Always switch off the unit and disconnect the power supply to the appliance before performing any cleaning tasks.
- Ensure no jet wash equipment or pressure washers are brought near the cabinet for sanitation tasks.
- Verify that all cleaning materials prepared for use are strictly non-abrasive to prevent toxic residue contamination.
- Prepare a supply of plain water exclusively for washing the magnetic door gaskets.
Safety warnings
- Always switch off and disconnect the power supply to the unit before cleaning.
- DO NOT use jet/pressure washers to clean the appliance.
- DO NOT allow oil or fat to come into contact with the plastic components or door seal.
- Do not use abrasive cleaning agents because these can leave harmful residues.
- Do not allow water used in cleaning to run through the drain hole into the evaporation pan.
- Take care when cleaning the rear of the appliance because sharp edges can cut.
- Do not remove any components or service panels on this product.
Initial Commissioning and First-Time Cleaning
Before using the appliance for the first time, clean the shelves and interior with soapy water.
Always switch off and disconnect the power supply to the unit before cleaning commences.
Always wipe dry after cleaning prior to stocking any commercial foodstuffs.
- Switch off and isolate the refrigeration unit from the mains electrical socket.
- Wash the interior storage liner and all removable shelves thoroughly with soapy water.
- Ensure that wash water does not enter the drain hole leading to the evaporation pan.
- Wipe all internal surfaces and shelving completely dry with a clean cloth.
Routine Interior and Shelf Sanitisation
Clean the interior of the appliance as often as possible to maintain sanitary conditions.
Do not use abrasive cleaning agents during routine maintenance because these can leave harmful residues.
Do not allow water used in cleaning to run through the drain hole into the evaporation pan.
Always wipe dry after cleaning to eliminate residual moisture from all food storage surfaces.
- Switch off the appliance power switch and unplug the electrical connection from the mains.
- Wash the interior surfaces using non-abrasive cleaning methods.
- Keep wash water strictly away from the internal drainage hole to protect the evaporation pan.
- Wipe all washed internal surfaces thoroughly dry before restoring electrical power.
Door Seal Protection and Maintenance
Clean the door seal with water only to preserve seal integrity.
DO NOT allow oil or fat to come into contact with the plastic components or door seal.
Clean immediately if contact with fat or oil occurs to prevent surface deterioration.
Always wipe dry after cleaning the door gaskets.
- Inspect the plastic components and flexible door gaskets for any food, oil, or fat spills.
- Clean immediately if contact occurs using only clean water on the door seals.
- Avoid using any abrasive cleaning agents on plastic parts or door seals.
- Wipe the door gaskets completely dry with a soft cloth.
Condenser Maintenance and Rear Cabinet Upkeep
Periodically cleaning the condenser can extend the life of the appliance.
Always switch off and disconnect the power supply to the unit before cleaning the condenser or cabinet exterior.
Take care when cleaning the rear of the appliance because sharp edges can cut.
Do not remove any components or service panels on this product during routine cleaning.
- Turn off the main appliance power switch and disconnect the plug from the electrical socket.
- Clean the condenser periodically without dismantling any service panels.
- Exercise extreme caution when wiping around the rear of the cabinet to avoid cut injuries from sharp metal edges.
- Wipe all external surfaces dry before reconnecting the appliance to the electrical mains.
Stop and get help if
- Stop immediately and do not attempt cleaning if the appliance cannot be safely disconnected from the power supply.
- Stop work immediately if component removal or service panel disassembly is required to access a part.
- Cease all cleaning operations if any repair or electrical fault is detected on the unit.
When to call an engineer
- A service agent or qualified technician should carry out installation and any repairs if required.
- Escalate to a qualified technician whenever components or service panels need to be removed on this product.