To safely clean and maintain your Combisteel 7073.0045 meat grinder every day, you must first turn off the machine, set the switch to the 0 position, and disconnect the electricity before disassembling the components and cleaning the exterior.
Applies to
These specific daily cleaning and maintenance instructions apply exclusively to the Combisteel 7073.0045 meat grinder model.
Before you start
- The trained operator must ensure that the machine is turned off after use.
- The operator must set the switch to the 0 position after using the machine.
- You must disconnect the electricity from the machine before starting daily cleaning.
- You must make sure that the electricity is completely disconnected before cleaning begins.
Safety warnings
- You must be careful not to cut your hand when removing the knife.
- You must clean the outside surface with a soaked wet cloth without touching any electrical parts.
- You must not let water touch the body of the machine.
- You must not use a wet cloth to clean the lower part of the device, even when disconnected from electricity.
- You must not use a wet cloth to clean the electrical control unit, even when disconnected from electricity.
- You must not use a wet cloth to clean the engine compartment, even when disconnected from electricity.
- You must be careful not to let water come into the lower part of the device.
- You must be careful not to let water come into the electrical control unit.
- You must be careful not to let water come into the engine compartment.
- You must not reassemble the parts until confirming they are completely dry.
Section 1: Post-Operation Shutdown Procedures
The trained operator must ensure that the machine is turned off after use.
The operator must set the switch to the 0 position after using the machine.
- Turn the machine off immediately after use.
- Set the machine switch to the 0 position after use.
Section 2: Mandatory Power Disconnection
You must disconnect the electricity from the machine before starting daily cleaning.
The operator must make sure that the electricity is disconnected before cleaning begins.
- Disconnect the electricity from the machine before starting daily cleaning.
- Verify that the electricity is disconnected before proceeding with the cleaning process.
Section 3: Opening the Grinder Assembly
You must open the bracelet during your daily maintenance routine.
You must use the provided apparatus to open the bracelet.
- Locate the provided apparatus delivered with your machine.
- Use the provided apparatus to open the bracelet.
Section 4: Removing the Internal Grinding Components
You must remove the mirror from the machine during daily maintenance.
You must pull out the spiral shaft during the daily maintenance process.
You must remove the knife from the machine assembly.
You must be careful not to cut your hand when removing the knife.
- Pull out the mirror from the machine.
- Pull out the spiral shaft from the machine.
- Pull out the knife from the machine.
- Exercise caution to ensure you do not cut your hand while removing the knife.
Section 5: Safe Exterior Cleaning Practices
You must clean the outside surface of the machine with a soaked wet cloth.
You must perform this exterior cleaning without touching any electrical parts of the device.
You must ensure that you do not touch the body of the machine with water.
- Prepare a soaked wet cloth for cleaning the outside surface.
- Clean the outside surface with the soaked wet cloth.
- Avoid touching any electrical parts of the device while cleaning the outside surface.
- Ensure that no water touches the body of the machine during this process.
Section 6: Strict Wet Cloth Restrictions
You must not use a wet cloth to clean the lower part of the device.
You must not apply a wet cloth to the electrical control unit.
You must not clean the engine compartment with a wet cloth.
You must adhere to these wet cloth restrictions even when the machine is disconnected from electricity.
- Do not apply a wet cloth to the lower part of the device, even if there is no electricity.
- Do not apply a wet cloth to the electrical control unit, even if there is no electricity.
- Do not apply a wet cloth to the engine compartment, even if there is no electricity.
Section 7: Preventing Water Ingress
You must be careful not to let water come into the lower part of the device.
You must be careful not to let water come into the electrical control unit.
You must be careful not to let water come into the engine compartment.
- Ensure that no water comes into the lower part of the device.
- Ensure that no water comes into the electrical control unit.
- Ensure that no water comes into the engine compartment.
Section 8: Drying and Reassembly Requirements
You must confirm the dryness of the parts before replacing them.
You must not reassemble the machine without confirming that the parts are completely dry.
- Inspect the removed parts to confirm their dryness.
- Do not replace the parts until you have confirmed they are completely dry.